![]() ![]() Observe light-emitting diodes (LEDs) for Power-On-Self Test (POST) results. Verify that the correct optical cable is attached.Ĥ. Verify that the HBA is securely installed in the computer.Ģ. FIGURE 3 Attaching the Optical CableĢ.Ĝonnect the other end of the cable to the Fibre Channel device.Īfter the optical cable is connected to the HBA, you are ready to apply power to the computer.ġ. Use multimode fiber-optic cable, with short-wave lasers, that adheres to the following specifications:ġ.Ĝonnect the fiber-optic cable to an LC connector on the HBA (see FIGURE 3). Note - The HBA will not allow normal data transmission on an optical link unless it is connected to another similar or compatible laser product (that is, multimode to multimode). The HBA is now installed in the computer and is ready for the optical cable attachment. Replace the computer case and tighten case screws. Secure the HBA's mounting bracket to the case with the panel screw or clip.Ĩ. Press firmly until the adapter is seated.ħ. Insert the HBA into the empty 32-bit or 64-bit PCI or PCI-X bus slot. Replace the screws that attach the HBA to the bracket.Ħ. Make sure the LEDs are properly aligned with the holes in the bracket.ĭ. Note - Be careful not to push the bracket past the transceiver housing's grounding tabs. Align the new mounting bracket tabs with the holes in the HBA. Remove the bracket and store it for future use.Ĭ. Remove the mounting bracket screws from the HBA (see FIGURE 2). (12.06 cm) long, and is provided with each X-option.Ī. A low-profile mounting bracket is shorter than the standard bracket, approximately 3.11 in. Note - The HBA comes with a standard PCI bracket installed. Optionally, perform the following steps to replace the PCI bracket. Remove the blank panel from an empty PCI or PCI-X bus slot.ĥ. Ensure that the PCI bus is not shared with another PCI card that can lower the PCI slot clock rate.Ĥ. Note - For best I/O performance, place the adapter into an empty PCI-X slot that is running at 133 MHz. Shut down, power off, and unplug the computer. Record these numbers before installation.Ģ. All numbers are clearly marked on the board. ![]() The serial number is used when communicating with Sun. The IEEE address is used when configuring your system. SG-XPCI2FC-EM2 HBA has two ports, it has two IEEE addresse s. The Fibre Channel industry uses a World Wide Name (WWN) derived from the IEEE address, and this number is needed for Fibre Channel connectivity. Place the HBA on a properly grounded antistatic work surface pad when it is out of its protective antistatic bag.Įach HBA is shipped with a unique 64-bit identifier called the IEEE address.Hold the HBA by the edge of the PCB or mounting bracket, not the connectors.Always use a properly fitted and grounded wrist strap or other suitable ESD protection when handling the HBA and observe proper ESD grounding techniques.Leave the HBA in its antistatic bag until you are ready to install it in the system.Observe the following precautions to avoid ESD-related problems: You can get an ESD wrist strap from any reputable electronics store or from Sun as part number #250-1007. To minimize the possibility of ESD-related damage, Sun strongly recommends using both a workstation antistatic mat and an ESD wrist strap. Always handle the HBA with care to avoid damage to electrostatic sensitive components. If necessary, consult your computer system manual for instructions to remove the computer cover.Ĭaution - Damage to the HBA can occur as the result of careless handling or electrostatic discharge (ESD). To install the Sun StorEdge Enterprise 2 Gb FC Single and Dual Port HBA, you need to open the computer and identify an empty PCI slot (32-bit or 64-bit). Sun StorEdge Enterprise 2 Gb FC Single and Dual Port HBA. ![]() Verify that the Sun StorEdge Enterprise 2 Gb FC Single and Dual Port HBA is shipped with the following items (see FIGURE 1): To Verify Proper Installation in BIOS Based Systems.To Verify Attached Storage to the Installed HBA.To Verify Proper Installation in SPARC Platforms.Follow these steps to install the Sun StorEdge Enterprise 2 Gb FC Single and Dual Port HBA in your system: ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |